The Perkins 1104D-E44T is a 4.4 L 4-cylinder turbocharged engine rated at 2200 rpm, producing up to 74.5 kW. It holds 8 L (2.1 gal) of oil and 7 L (1.8 gal) of coolant.
Part of the Perkins 1104D engine family — 16 variants share parts & fitment.
| Oil capacity | 8.0 L |
|---|---|
| Coolant capacity | 7.0 L |
| Displacement | 4.4 L |
| Cylinders | 4 |
| Aspiration | Turbocharged |
| Rated speed | 2200 rpm |
| Gross power | 74 kW |
No generator set in our catalog cites this exact engine designation yet; its specifications and fault codes are documented here.
| Code | Meaning | Remedy |
|---|---|---|
| 551 | No Detected Faults have occurred since the ignition keyswitch has been turned to the ON position | Flash Code 551 indicates no faults. No further action required. |
| 111 | No. 1 Injector Fault | Schedule a Service. |
| 112 | No. 2 Injector Fault | Schedule a Service. |
| 113 | No. 3 Injector Fault | Schedule a Service. |
| 114 | No. 4 Injector Fault | Schedule a Service. |
| 133 | Intake Manifold Air Temperature sensor fault | Schedule a Service. |
| 141 | Primary Engine Speed/Timing Sensor Fault | Schedule a Service. |
| 142 | Secondary Engine Speed/Timing Sensor Fault | No specific remedy provided, but it is suggested to investigate the fault. |
| 143 | Engine Timing Calibration Fault | Schedule a Service. |
| 144 | Engine Operation Mode Selector Switch Fault | Schedule a Service. |
| 151 | Air Inlet Pressure Sensor Fault | Schedule a Service. |
| 154 | Throttle Position Sensor Fault | Schedule a Service. |
| 155 | Secondary Throttle Position sensor Fault | Schedule a Service. |
| 157 | Engine Oil Pressure Sensor Fault | Schedule a Service. |
| 159 | Fuel Rail Pressure Sensor Fault | Schedule a Service. |
| 162 | Fuel Rail Pressure Valve Solenoid Fault | Schedule a Service. |
| 168 | Engine Coolant Temperature Sensor Fault | No specific remedy provided, but it is suggested to investigate the fault. |
| 169 | Low Engine Coolant | No specific remedy provided, but it is suggested to investigate the fault. |
| 177 | Turbo Wastegate Actuator Fault | No specific remedy provided, but it is suggested to investigate the fault. |
| 185 | High Exhaust Temperature | No specific remedy provided, but it is suggested to investigate the fault. |
| 197 | Intake Manifold Boost Pressure Fault | Schedule a Service. |
| 199 | Glow Plug Start Relay Fault | No specific remedy provided, but it is suggested to investigate the fault. |
| 233 | Ether Injection Control Solenoid | Schedule a Service. |
| 245 | Idle Validation Switch 1 Fault | No specific remedy provided, but it is suggested to investigate the fault. |
| 246 | Idle Validation Switch 2 Fault | No specific remedy provided, but it is suggested to investigate the fault. |
| 253 | Engine Fuel Supply Pump Relay Fault | Schedule a Service. |
| 415 | Software Mismatch | No specific remedy provided, but it is suggested to investigate the fault. |
| X | Warning lamps are installed. | Refer to this table. For installations that have electronic displays, refer to the OEM for information. |
| 511 | ECM Power Supply Voltage Fault | |
| 514 | SAE J1939 Data Link Fault | |
| 516 | 5 Volt Sensor DC Power Supply Fault | |
| 517 | 8 Volt Sensor DC Power Supply Fault | |
| 527 | Customer/System Parameter Fault |
| Symptom | Cause | Remedy |
|---|---|---|
| Diagnostic lamp is activated | System detects an active problem | Refer to Troubleshooting, “Electronic Service Tools” for further information. |
| Active codes represent problems that currently exist | These problems should be investigated first. | |
| Logged codes represent intermittent problems, recorded events, and performance history | The problems may have been repaired since the logging of the code. These codes do not indicate that a repair is needed. | |
| Diagnostic lamp illuminates during normal engine operation. | Use electronic service tools to check the active diagnostic codes. | |
| Low oil pressure condition with 'DERATE' selected. | The Electronic Control Module (ECM) will limit the engine power until the problem is corrected. If the oil pressure is within the normal range, the engine may be operated at the rated speed and load. | |
| Active diagnostic code should be investigated. | The cause of the problem should be corrected as soon as possible. If the cause of the active diagnostic code is repaired and there is only one active diagnostic code, the diagnostic lamp will turn off. | |
| Diagnostic lamp illuminates during normal engine operation and shuts off. | An intermittent fault may have occurred. The operator should retrieve the logged fault codes and reference the appropriate information in order to identify the nature of the event. | |
| System configuration parameters affect the emissions or power of the engine. | The electronic service tool is required to alter the configuration parameters. System configuration parameters are programmed at the factory and do not require reprogramming if the ECM software is changed. |
Fault codes and symptom→remedy steps extracted from this engine’s service/owner documentation; verify against the official manual before servicing.
| Part # | Description | Category |
|---|---|---|
| P532 | Fuel Injection Pump Solenoid Connector (2 Pin Connector) | connector |
| g01264578 | Coolant flow | coolant_flow |
| i02234878 | Electrical System | electrical_system |
| i02403276 | Electrical System | electrical_system |
| i02321383 | Engine Electronics | engine_electronics |
| i01958113 | Engine Specification | engine_specification |
| g01249050 | Secondary Fuel Filter | fuel filter |
| g01266023 | Fuel Injection Pump | fuel injection pump |
| g01201611 | Fuel Injectors | fuel injectors |
| g01266024 | Fuel Manifold | fuel manifold |
| g01265623 | Fuel Priming Pump | fuel priming pump |
| g01265683 | Fuel Transfer Pump | fuel transfer pump |
| N378886 | WATER SEPARATOR | fuel_filter |
| RE526657 | RE544394 FINAL FUEL FILTER | fuel_filter |
| RE546336 | RE541922 RE522868 RE509208 PRIMARY FUEL FILTER | fuel_filter |
| g00704135 | Fuel filter | fuel_filter |
| g01259333 | The fuel injection pump and related components | fuel_pump |
| i02074845 | Fuel System | fuel_system |
| i02406189 | Cleanliness of Fuel System Components | fuel_system_cleanliness |
| g01236714 | Diagram of the basic fuel system (typical example) | fuel_system_diagram |
| i01958097 | General Information | general_information |
| g01162916 | Engine Electronics - Grounding Practices | grounding_practices |
| g01244554 | Illustration 12 - High Pressure Fuel Lines | high_pressure_fuel_line |
| i02378733 | High Pressure Fuel Lines | high_pressure_fuel_line |
| g01288650 | High pressure fuel system (typical example) | high_pressure_fuel_system |
| g00281646 | Illustration 7 | illustration |
| g00302786 | Illustration 8 | illustration |
| g00984281 | Illustration 1 | illustration |
| g00993373 | Illustration 3 | illustration |
| P691/J691 | Electronic Unit Injectors for No. 1 and No. 2 Cylinders (4 Pin Connector) | injector |
| P692/J692 | Electronic Unit Injectors for No. 3 and No. 4 Cylinders (4 Pin Connector) | injector |
| g01265309 | Low pressure fuel system (typical example) | low_pressure_fuel_system |
| g01264620 | Flow diagram of the lubrication system | lubrication_system |
| g00704059 | Oil filter | oil_filter |
| g00104545 | Illustration 4 | other_service |
| g00687600 | Always use a board or cardboard when you check for a leak. Leaking fluid that is under pressure can penetrate body tissue. | other_service |
| g00702020 | Wear a hard hat, protective glasses, and other protective equipment, as required. | other_service |
| g01012280 | (1) Tapa del mecanismo de válvulas (2) Respiradero del cárter (3) Filtro de combustible (4) Bomba de inyección de combustible (5) Filtro de aceite del motor (6) Polea del cigüeñal (7) Bomba de agua (8) Polea del ventilador (9) Caja del termostato del agua | other_service |
| g01154807 | Typical example | other_service |
| g01154858 | Typical example | other_service |
| g01187485 | Cylinder and valve location (Illustration 22) | other_service |
| g01205681 | Air Inlet and Exhaust System Components | other_service |
| g01245940 | Rear right engine view | other_service |
| g01245941 | Front left engine view | other_service |
| g01263698 | Typical Cylinder Block | other_service |
| g01263700 | Typical cylinder head | other_service |
| g01263701 | Pistons, Rings and Connecting Rods | other_service |
| g01263702 | Crankshaft | other_service |
| g01263703 | Gears and Timing Gear Case | other_service |
| g01263705 | Illustration of gears and timing gear case | other_service |
| g01263706 | Camshaft | other_service |
| g01263708 | Rocker Shaft Assembly | other_service |
| g01268960 | Hand (High Pressure) | other_service |
| g01426636 | Ether | other_service |
| g03450122 | Hand (High Pressure) | other_service |
| g03450123 | The warning label for the Hand (High Pressure) (2) | other_service |
| g03452577 | Grounding Practices (Illustration 15) | other_service |
| g03452579 | Grounding Practices (Illustration 16) | other_service |
| g03453612 | Serial Number Plate (Illustration 24) | other_service |
| i01372247 | Inspect the steps, the hand holds, and the work area before mounting the engine. Keep these items clean and keep these items in good repair. | other_service |
| i01928905 | Never disconnect any charging unit circuit or battery circuit cable from the battery when the charging unit is operating. A spark can cause the combustible gases that are produced by some batteries to ignite. | other_service |
| i02143194 | Support the component correctly when work beneath the component is performed. | other_service |
| i02157341 | Before Starting Engine NOTICE For initial start-up of a new or rebuilt engine, and for start-up of an engine that has been serviced, make provision to shut the engine off should an overs peed occur. This may be accomplished by shutting off the air and/or fuel supply to the engine. | other_service |
| i02197956 | Record the information in the appropriate space. Make a copy of this list for a record. Keep the information for future reference. | other_service |
| i02207232 | Do not use aerosol types of starting aids such as ether. Such use could result in an explosion and personal injury. | other_service |
| i02234873 | Engine Stopping (Operation Section) | other_service |
| i02235492 | Mounting and Dismounting | other_service |
| i02251260 | Engine Starting | other_service |
| i02322199 | Before Starting Engine | other_service |
| i02328435 | General Hazard Information | other_service |
| i02330192 | Monitoring System | other_service |
| i02334785 | Burn Prevention | other_service |
| i02378728 | Safety Messages | other_service |
| i02517251 | Introduction | other_service |
| i02525716 | Basic Engine Introduction | other_service |
| i02864025 | Safety Messages | other_service |
| i04823662 | Fire Prevention and Explosion Prevention | other_service |
| i05272352 | Engine Electronics (Operation Section) | other_service |
| i05302522 | Burn Prevention | other_service |
| i05461290 | Safety Messages | other_service |
| i05463929 | Mounting and Dismounting | other_service |
| i05463931 | High Pressure Fuel Lines | other_service |
| i05464430 | Electrical System Never disconnect any charging unit circuit or battery circuit cable from the battery when the charging unit is operating. | other_service |
| i05536748 | Product Information - General Information | other_service |
| i05536753 | Product Description - Off Engine Parts and Options | other_service |
| i05536932 | Product Identification - Information (Illustration 23) | other_service |
| i05537598 | Gauges and Indicators (Illustration 31) | other_service |
| i05546770 | Monitoring System | other_service |
| i07451407 | Operation Section - Lifting and Storage (Illustration 26) | other_service |
| i08315117 | General Hazard Information | other_service |
| P100 | Coolant Temperature Sensor (2 Pin Connector) | sensor |
| P103 | Intake Manifold Temperature Sensor (2 Pin Connector) | sensor |
| P200 | Intake Manifold Pressure Sensor (3 Pin Connector) | sensor |
| P201 | Engine Oil Pressure Sensor (3 Pin Connector) | sensor |
| P228 | Fuel Pressure Sensor (3 Pin Connector) | sensor |
| P401 | Primary Speed/Timing Sensor (2 Pin Connector) | sensor |
| P402 | Secondary Speed/Timing Sensor (2 Pin Connector) | sensor |
| g01216877 | Starting Motor (12 Volt) | starting_motor_12v |
| g01200801 | Starting Motor (24 Volt) | starting_motor_24v |
| g01012281 | (1) Tapa de llenado de aceite (2) Múltiple de escape (3) Alternador (4) Turbocompresor (5) Motor de arranque (6) Caja del volante (7) Volante (8) Admisión de aire | turbocharger |
| g01263770 | Turbocharger | turbocharger |
| g03506649 | Turbocharge Engine View (Illustration 20) | turbocharger |
| i02527637 | Valve system components | valves |
| g01287919 | Typical turbocharger with the wastegate | wastegate |
| P601 | Wastegate Valve (if equipped) (2 Pin Connector) | wastegate valve |
| g00765012 | Welding on Engines with Electronic Controls | welding_procedures |
Parts cataloged across all variants of this engine family — verify the exact part fits your specific variant and serial number before ordering.
Parts listed by aftermarket suppliers as fitting this engine — leads compiled from supplier catalogs; verify the exact part for your serial number.
The Perkins 1104D-E44T engine has an oil capacity of 8.0 liters.
The Perkins 1104D-E44T has a displacement of 4.4 liters with 4 cylinders.